Double-Layered Tuque Pattern

I finished up a second of my extremely-warm double-layered winter hats the other day, this time for Thing 1, and I thought I’d share the pattern. It’s a pretty easy one, as such things go. It involves the basic techniques of casting on, casting off, knitting, purling, increases (k1fb — knit one front and back), decreases (k2tog — knit two together), and knitting in the round (I prefer the magic loop technique, but whatever you are most comfortable with is fine). Don’t let the seemingly long pattern deter you! It’s mostly because the pattern contains a flat-brim and a ribbed-brim version.

A note about sizing: this hat is made to fit my 23″ head with room for a ponytail or other hairdo underneath. I’m no Brent Butt (who claims to have a 27″ head), but my head’s still large enough that it generally falls outside of the women’s hat sizing category and smack-dab into the men’s. Don’t worry, this pattern is adjustable to the size that you want it; instructions are below.

Left: plain brim hat knit in Polo Stripe colourway
Right: ribbed brim hat knit in Favorite Stripe colourway

Double-Layered Tuque
Adult male size, fits 23″ to 24″ circumference head

Materials:
– one 141g (5oz), 215m (236 yds) ball of Red Heart Super Saver Stripes yarn (100% acrylic)
– for ribbed-brim hat only: scraps of contrasting yarn for stitches & pompom
– one set of 5mm (US 8, UK 6) circular knitting needles in a length comfortable for the magic loop method (I prefer 120cm/47″ or longer)

Gauge:
– 21 stitches and 27 rows in stockinette stitch = 20cm x 20cm (4″ x 4″) square on 5mm (US 8, UK 6) needles

Instructions:

Cast on:
– Cast on 18 stitches (flat brim) OR 24 stitches (ribbed-brim).
– Place half of the stitches on each half of the circular needle so as to use the magic loop method.
– Join to work in the round, being careful not to twist.
– Knit one row, placing a stitch marker after every third (flat brim) OR fourth (ribbed brim) stitch. This will divide your work into six sections.

Increase the Crown Exterior:
– First row: *Knit until one stitch before first stitch marker. K1FB on the stitch before the stitch marker. Repeat from * until row is complete. (Every row like this will increase your work by 6 stitches.)
– Second row: Knit.
– Repeat first and second rows until you have 57 stitches per side (flat brim) OR 60 stitches per side (ribbed brim)

SIZING NOTE:

This is where you can adjust for head size. Once you have established your gauge, which you can do either with a swatch or by measuring your stitches as you go, you can calculate how many stitches you will need in total. Use one of the following formulae, depending on whether you’re measuring in metric or imperial:

(Head Circumference + 2.5cm) X Number of Stitches per CM = Desired # of Stitches

OR

(Head Circumference + 1″) X Number of Stitches per Inch = Desired # of Stitches

Then, round the stitch number up to the next multiple of six. It gets a bit more tricky for the ribbed brim version, which must also be divisible by four.

Knit the Body:
– Use a piece of differently-coloured yarn or a safety pin to mark the row where the increases end.
FLAT-BRIM:
– Knit until body measures 9cm (3.5″) from end of increases.
– Remove increase marker.
RIBBED-BRIM:
– Knit until body measures 5cm (2″) from end of increases.
– K2, P2 for and additional 3.8cm (1.5″).
– Remove increase marker.

Decrease:
FLAT-BRIM:
– Divide the number of stitches on each needle by three, and place a stitch marker after each group. Knit the next round, knitting two stitches together for the two stitches before each stitch marker. There should be 54 stitches on each needle.
RIBBED BRIM:
– Divide the number of stitches on each needle by two, and place a stitch marker after each group. Knit OR purl two stitches together, depending on what that stitch should have been in the normal order of K2, P2. There should be 58 stitches on each needle.
– Use a piece of differently-coloured yarn or a safety pin to mark the row where you made these decreases.

Knit the Body Lining:
FLAT BRIM:
– Knit until interior body measures 9cm (3.5″) from decrease marker.
– Remove decrease marker.
RIBBED BRIM:
– K2, P2 for 3.8cm (1.5″) from decrease marker.
– Knit for an additional 5cm (2″).
– Remove decrease marker.

Decrease Lining:
– Divide the number of stitches on each needle by three. For the flat-brimmed hat, unless you have adjusted for size, that means each group should be 18 stitches. For the ribbed-brim hat, the number will not be even. If you have not adjusted for size, divide the stitches 19-19-20. If you have adjusted for size, try and make the groups as even as possible.
– First row: **Knit until two stitches before first stitch marker. K2tog on the two stitches before the stitch marker. Repeat from ** until row is complete. (Every row like this will decrease your work by 6 stitches.)
– Second row: Knit.
– Repeat first and second rows until you have 12 stitches per side (flat brim) OR 18 stitches per side (ribbed brim).
– Cast off, leaving a long tail.

Finishing:
– Run the tail of yarn through the cast off stitches and draw tight, tying a secure knot.
– Run the other tail of yarn through the cast on stitches and pull tight, tying a secure knot.
– Fold the lining into the exterior of the hat so that the cast off and cast on stitches touch, back to back.
– With a few stitches of one of the yarn tails, secure the two ends of the hat together at the point. Tie one tail to the other and pull them between the two layers of fabric.
– Create a pompom out of the leftover yarn (flat brim) or out of scrap contrasting yarn (ribbed brim). Stitch it to the exterior of the peak of the hat.
– About 1cm (about 0.5″) from the bottom edge of the hat (flat brim) OR along the edge of the ribbing (ribbed brim), stitch leftover/contrasting yarn every second stitch, affixing the lining to the exterior of the hat. Then run a piece of leftover/contrasting yarn through these stitches, creating a continuous line. Make sure that these stitches are not too tight, so as not to be uncomfortable around the ears. Tie off the yarn and run it between the two layers of fabric, snipping off any extra if it protrudes.

As usual, should you note any errata in this pattern, or if any instructions need further clarification, please let me know so that I can fix it and/or make my instructions more clear!